Seattle skyline with the Space Needle in the foreground

Seattle, WA

Mold Remediation in Seattle: Independent Protocols, Oversight & Clearance

Citadel EHS does not do the removal work. We write the protocol, oversee your contractor and verify the result with clearance testing.

Photo: Evan Clark / Unsplash

What we do, and what we don’t

Plainly: we do not perform remediation labor. No Citadel crew will tear out drywall or set containment in your building. A remediation contractor does the physical work.

We handle the work around it. We assess the damage and the water source, write the protocol and scope of work, compare contractor bids against that scope, oversee the work on site and perform post-remediation verification testing once the contractor reports completion.

Our independence from the contractor is the point. The person judging whether the job is clean is not the person who was paid to clean it.

Why oversight matters in Seattle

In occupied Seattle buildings, remediation happens near people: tenants, employees, patients or students. A protocol sets out how the work area is isolated and cleaned, so that occupants outside the work area are not exposed to what is being disturbed.

Many remediation jobs follow a water event, and insurers, owners and tenants may all want a record of what was found and what was done. A scope written before the work and a verification report after it give that record without relying on the contractor’s own paperwork.

Where the building is older, tear-out may also disturb asbestos-containing materials. Puget Sound rules require a survey by an AHERA building inspector before a renovation, covered below.

Guidance and rules that apply

There is no numeric mold limit to clear against, so remediation follows published guidance. The asbestos survey rule applies to the renovation that remediation often involves.

  • EPA guidance for commercial buildings

    EPA’s guidance on mold remediation in schools and commercial buildings says to use outside professionals with mold cleanup experience, check their references, and have them follow EPA’s recommendations, ACGIH guidelines or other professional guidelines.

    EPA, Mold Remediation in Schools and Commercial Buildings, Chapter 1
  • ANSI/IICRC S520

    The ANSI/IICRC S520 standard is a procedural standard for the remediation of mold-damaged structures and contents in residential, commercial and institutional buildings. The fourth edition was published in 2024.

    IICRC, ANSI/IICRC S520
  • RCW 59.18.060(14)

    Residential landlords must give new tenants Washington Department of Health information on the health hazards of indoor mold when the lease is signed, or post it in a visible public location.

    Washington RCW 59.18.060
  • PSCAA Regulation III, Section 4.02

    It is unlawful to cause or allow a renovation unless the property owner or the owner’s agent determines whether there are suspect asbestos-containing materials in the work area and obtains an asbestos survey of them by an AHERA building inspector. An AHERA inspector is not required for an owner-occupied single-family residence.

    Puget Sound Clean Air Agency, Regulating Asbestos

How a remediation project runs

  1. Step 1

    Assessment

    We inspect the affected area, find the moisture source and decide how far the work needs to extend.

  2. Step 2

    Protocol and scope

    We write the protocol: the work to be done, how it is contained and cleaned, and the criteria the space must meet to be cleared.

  3. Step 3

    Bid review

    You invite the contractors you want. We help you compare what they offer against the same written scope.

  4. Step 4

    Oversight during the work

    We visit the site while work is under way, check it against the protocol and record what we see.

  5. Step 5

    Clearance testing

    When the contractor reports completion, we inspect and perform post-remediation verification testing against the protocol’s criteria.

You receive the written protocol before the work begins and a clearance report afterwards, with our inspection findings and laboratory results.

Mold Remediation in Seattle: common questions

Does Citadel EHS remove the mold?
No. We are an independent consultant, so we write the protocol, oversee the contractor and perform clearance testing, but we do not do the removal ourselves.
Why is independence from the contractor useful?
A contractor that writes the scope and grades its own work has a conflict of interest between the size of the scope and the verdict. When we do neither, the scope and the verification are not tied to the contractor’s revenue.
How does remediation work in an occupied Seattle building?
The protocol covers how the work area is isolated from occupied space and how it is cleaned. We check that on site while the work is under way. The details depend on the building and what is being removed.
Do we need an asbestos survey before tear-out?
Puget Sound Clean Air Agency Regulation III, Section 4.02 requires a survey by an AHERA building inspector before a renovation, except for an owner-occupied single-family residence. Whether your project is a renovation under the regulation is worth confirming. Our Seattle asbestos testing page covers the survey.
What does clearance testing check?
It checks the space against the criteria set in the protocol, usually a visual inspection plus sampling. EPA notes that surface sampling may be useful for determining that an area has been adequately remediated.
What if the spore counts are low but the area is still damp?
Treat the moisture as the problem. EPA says moisture control is the key to mold control, and a damp wall cavity can grow mold after a clean sample. Clearance includes confirming that the source is fixed and the materials are dry.

Request a consultation

Mold Remediation in Seattle, WA

By submitting, you'll also receive our newsletter. You can unsubscribe at any time.

Inquiring about Mold Remediation in Seattle