
Oregon
Mold Remediation in Oregon: Independent Protocols, Oversight & Clearance
Citadel EHS does not perform the tear-out. We write the remediation protocol, oversee the contractor who does the work, and verify the result with clearance testing.
What we do, and what we don’t
To be direct: Citadel EHS does not do remediation labor. We do not remove drywall, build containment or bid the work. A remediation contractor does that.
What we do is the part that decides whether the job works. We assess the affected area and the moisture source, write the remediation protocol and scope, help you review contractor bids against it, oversee the work while it is under way, and perform post-remediation verification testing at the end.
Because we have no stake in the removal work, the scope is not padded and the clearance result is not self-graded. That independence from the contractor is the reason to hire us.
Remediation oversight across Oregon
The Oregon Health Authority says there are no standards to judge “safe” levels of indoor mold. Clearance criteria therefore have to be written into the protocol before the work starts, and that is true in every Oregon county.
A mold job that leaves the moisture source in place usually comes back, especially in the wet western half of the state. A protocol that names the source, the repair and the order of work keeps the remediation contractor and the plumbing or roofing trade from undoing each other.
Tear-out raises a second question. Removing walls, ceilings or flooring to reach mold can disturb asbestos-containing materials. Oregon DEQ defines renovation to include replacing, stripping or repairing walls, ceilings and flooring, and the owner or operator must have an accredited inspector complete an asbestos survey first, with exemptions. Our Oregon asbestos testing page covers that rule.
Our Portland office writes protocols, visits the site during the work and performs clearance testing in the Portland metro area and the Willamette Valley. For other parts of Oregon, call us and we will scope the project.
Guidance and rules that apply
There is no numeric mold limit to clear against, so remediation work follows published guidance. The asbestos survey rule applies to the demolition or renovation that remediation often involves.
EPA guidance for commercial buildings
EPA’s guidance on mold remediation in schools and commercial buildings says to use outside professionals who have experience with mold cleanup, check their references, and have them follow EPA’s recommendations, ACGIH guidelines or other professional guidelines.
EPA, Mold Remediation in Schools and Commercial Buildings, Chapter 1ANSI/IICRC S520
The ANSI/IICRC S520 standard describes the procedures and precautions for mold remediation in residential, commercial and institutional buildings. The fourth edition was published in 2024.
IICRC, ANSI/IICRC S520No standard for “safe” levels
The Oregon Health Authority says there are no standards to judge “safe” levels of indoor mold. Clearance criteria therefore have to be written into the protocol before the work starts.
Oregon Health Authority, MoldOAR 340-248-0270 and 340-248-0010
Before a demolition or renovation, the owner or operator must have an accredited inspector complete an asbestos survey, subject to the exemptions in OAR 340-248-0250. Oregon DEQ defines renovation to include replacing, stripping or repairing walls, ceilings and flooring.
Oregon Administrative Rules, chapter 340, division 248
How a remediation project runs
Step 1
Assessment
We inspect the affected area, identify the moisture source and decide how far the work needs to extend.
Step 2
Protocol and scope
We write the remediation protocol: the work to be done, containment and cleaning requirements, and the criteria the space must meet before it is cleared.
Step 3
Contractor selection
You send the protocol to the contractors you want to hear from. We help you compare their bids against the same scope.
Step 4
Oversight during the work
We visit the site while work is under way to confirm the contractor is following the protocol, and we document what we see.
Step 5
Clearance testing
When the contractor says the work is done, we inspect and perform post-remediation verification testing against the criteria in the protocol.
You receive the written protocol before work starts and a clearance report at the end with our inspection findings and laboratory results.
On the ground
Our Portland office
1120 SE Madison Street
Portland, OR 97214
(818) 246-2707
Based in Portland
Who you will work with
Mold Remediation in Oregon: common questions
- Do you do the mold removal yourselves?
- No. Citadel EHS is an independent consultant and does not perform remediation labor. We write the protocol, oversee your contractor and verify the result.
- Why not just hire one firm to test and remove?
- When one firm writes the scope, does the work and declares it done, there is no independent check. Separating the roles gives you a scope to bid against and a clearance result that is not self-graded.
- Can you recommend an Oregon remediation contractor?
- We write the protocol so that any qualified contractor can bid on the same scope. The choice of contractor stays with you.
- What does clearance testing check?
- It checks the space against the criteria in the protocol, usually a visual inspection plus sampling. EPA notes that surface sampling may help show whether an area has been adequately cleaned or remediated.
- Do we need an asbestos survey before tear-out?
- In many Oregon buildings, yes. DEQ requires an accredited inspector’s survey before a renovation, which the rule defines to include replacing or repairing walls, ceilings and flooring. There are exemptions, such as for an owner-occupant doing work inside a single-unit private residence, so confirm your case.
- Is the process different outside Portland?
- The protocol, oversight and clearance steps are the same. The Oregon Health Authority guidance and the DEQ asbestos rule are not specific to one city. Travel and scheduling depend on where the building is, so call us with the address.