
San Francisco Bay Area, CA
Mold Inspection & Testing in San Francisco & the Bay Area
Independent mold inspection and testing for San Francisco and Bay Area property managers, facility teams and building owners, with a written report that stands apart from any repair bid.
What we do
Citadel EHS starts a mold investigation with the water. A consultant reviews the building’s leak and repair history, maps wet materials with moisture readings and infrared imaging, and takes air or surface samples only where the result will answer a question.
We do not sell remediation, so the findings are not tied to a bid. The report states what is wet, what is causing it and how far it extends. Owners use it to scope repairs and to document conditions for a lease, a sale or a claim.
Our Walnut Creek office, the Bay Area headquarters, serves San Francisco, Oakland, the East Bay and the Tri-Valley.
Mold in Bay Area buildings
San Francisco and Oakland have many older wood-frame buildings, and many units sit at or below grade or are cut into hillsides. Those are places where groundwater, drainage and poor ventilation show up as damp walls and musty rooms.
The Bay Area’s cool, foggy summers and wet winters also leave cold surfaces for condensation to form on. CDPH lists steam from showers and cooking, humidifiers and clothes dried indoors among common sources of indoor moisture, and in a tight apartment these add up.
CDPH puts it plainly: moisture is the limiting factor that determines whether mold can grow. In most Bay Area jobs we start with the building envelope, plumbing and ventilation, not with a spore count.
What the rules say about mold testing in California
Mold is not regulated like asbestos. These points shape how we plan sampling for Bay Area owners.
No federal mold limits
EPA states that no EPA or other federal limits have been set for mold or mold spores, so sampling cannot be used to check a building’s compliance with a federal mold standard.
EPA, A Brief Guide to Mold, Moisture and Your HomeCDPH on moisture and mold
CDPH says that moisture or dampness is the limiting factor that determines whether mold can grow, and that if you can see mold, water damage or moisture, or smell mold, there is at least some increased health risk.
CDPH, Mold and DampnessH&S Code 26102 and 26103
Under the Toxic Mold Protection Act, the state health department was directed to consider the feasibility of adopting permissible exposure limits for mold in indoor environments, and to adopt them if feasible. CDPH reports that the evidence did not support doing so in 2005.
California Health & Safety Code 26102
How an inspection works
Step 1
Intake call
You describe the complaint, the building and any repairs. We say whether sampling will help or whether the moisture source needs to be found first.
Step 2
Site visit
We check walls, ceilings and below-grade or hillside-facing spaces with moisture readings and infrared imaging.
Step 3
Sampling plan
Where sampling is useful, we set locations and methods, with outdoor or unaffected-area comparison samples.
Step 4
Laboratory analysis
A laboratory analyzes the samples and we review the results.
Step 5
Written report
You receive findings, results and recommended next steps in one report.
You receive a written report with our findings, the laboratory results and recommendations from an independent consultant who is not bidding on the repair.
On the ground
Our Walnut Creek office
1371 Oakland Blvd Suite 100
Walnut Creek, CA 94596
(818) 246-2707
Mold Inspection & Testing in San Francisco Bay Area: common questions
- Is there a California limit for mold in a building?
- No. EPA says there are no federal limits, and CDPH reported in 2005 that the evidence did not support setting state exposure limits. We interpret results against outdoor and unaffected-area samples and the moisture condition.
- Why start with moisture instead of a spore count?
- CDPH says moisture is the limiting factor for mold growth, and EPA says moisture control is the key to mold control. A clean air sample does not mean a wet wall cavity is safe.
- Do you inspect garden-level and below-grade units?
- Yes. These spaces are where water from drainage, groundwater or poor ventilation tends to show first. We check walls and floors with moisture readings and infrared imaging and look at the exterior drainage that feeds them.
- Can you tell us whether the mold is from a leak or from condensation?
- Usually. A pattern on exterior walls and cold corners points to condensation, while staining below a fixture or roof penetration points to a leak. The visit documents which it is and what to fix.
- Which Bay Area cities do you serve?
- Our Walnut Creek office serves San Francisco, Oakland, Berkeley, Concord, Hayward, Richmond, Pleasanton, Livermore, San Ramon and Dublin, along with the East Bay and the Tri-Valley.
- Do you do the repair or cleanup?
- No. We are independent of the repair trades. If cleanup is needed, see our San Francisco mold remediation page for how we write the protocol and verify the result.